

REF: BROCADE5100
Fabricante: Brocade
Modelo: NA-5120-0008
Características:
Cabling Type: Fiber optic
Subcategory: Fibre Channel and SAN
Type: Switch
Connectivity Technology: Wired
Data Link Protocol: 8Gb Fibre Channel
Features: Trunking, Full duplex capability, Auto-sensing per device, ISL support, Manageable, Firmware upgradable
Ports Qty: 24
Remote Management Protocol: SNMP 1, SNMP 3, HTTPS, HTTP, Telnet
Data Transfer Rate: 8.5 Gbps
INTERFACE PROVIDED
Type: Management, Management, USB, Network
Interface: Ethernet 10Base-T/100Base-TX, RS-232, 8Gb Fibre Channel
Qty: 1, 1, 1, 24
Connector Type: RJ-45, RJ-45, LC
CHASSIS
Installed Devices / Modules: Qty 24
Supported Devices / Modules: Qty 40
Consola:
The system is coming up, please wait...
U-Boot 1.1.3 (May 4 2012 - 08:34:20)
CPU: AMCC PowerPC 440EPx Rev. A at 660 MHz (PLB=132, OPB=66, EBC=33 MHz)
No Security/Kasumi support
I2C boot EEPROM enabled
Bootstrap Option G - Boot ROM Location I2C (Addr 0x54)
Internal PCI arbiter enabled, PCI async ext clock used
32 kB I-Cache 32 kB D-Cache
Board: Spirit
I2C: ready
DRAM: Initializing DDRSDRAM
DDR Init: speed = 132000002
DQS calibration - Window detected:
max_passing_cases = 56
wr_dqs_shift = 95
dll_dqs_delay_X = 31
dll_dqs_delay_X window = 4 - 59
DDR0_09=0x00011d5f
DDR0_22=0x00267f0b
DDR0_17=0x1f005c00
DDR0_18=0x1f1f1f1f
DDR0_19=0x1f1f1f1f
ECC Enabling DONE
512 MB
POST RAM test disabled.
Now running in RAM - U-Boot at: 1fb2f000
trap_init : 0x0
system inventory subsystem initialized
FLASH: Spirit CFI Flash Driver Initialized
4 MB
ATA interface setup: io_base=0xf8f00000, port=0x3e0, ctl=0x7ec
PCI:
Skip our host bridge
00 07 1657 0010 0280 18
In: serial
Out: serial
Err: serial
Net:
Checking system RAM - press any key to stop test
Checking memory address:
System RAM test using Default POST RAM Test succeeded.
set_bootstatus: BS_LOAD_OS, platform_idx = 3
Type run flash_nfs to mount root filesystem over NFS
Hit ESC to stop autoboot:
Map file at LBA sector 0x8c0df
## Booting image at 00400000 ...
Image Name: Linux-2.6.14.2
Image Type: PowerPC Linux Multi-File Image (uncompressed)
Data Size: 4269595 Bytes = 4.1 MB
Load Address: 00000000
Entry Point: 00000000
Contents:
Image 0: 3190918 Bytes = 3 MB
Image 1: 1078663 Bytes = 1 MB
## Current stack ends at 0x1FAEDBE8 => set upper limit to 0x00C00000
## initrd at 0x0070B0D4 ... 0x0081265A (len=1078663=0x107587)
Loading Ramdisk to 1f9e5000, end 1faec587 ... OK
initrd_start = 1f9e5000, initrd_end = 1faec587
## Transferring control to Linux (at address 00000000) ...
Installing Linux 2.6 Kernel
Attempting to find a root file system on hda1...
INIT: version 2.78 booting
Bypassing firmware validation.
INIT: Entering runlevel: 3
Starting Fabric OS Services...
FIPS off, RRD...
Found 1(threshold 5) abnormal reboots within 3000 seconds window(threshold)
rscmon_service: started thread!
rscmon_service: started thread!
sys_chip_init: class 0 max 24 Done
ethsw_ha_enabled = 1
uptime: 4293889278
Consumo de energía: Consumo nominal del sistema 84 vatios máx. 91 vatios
Garantía: 24 meses